1、 適用材質：金屬、電鍍、氧化鋁、電解板、鋁塑板、噴（烤）漆、噴塑、PA塑料尼龍、電木、玻璃鋼、密胺等。2、 產品特性：半光、免烘烤、耐酒精、耐沖壓。3、 稀釋劑：本公司B-03稀釋劑或783慢干稀釋劑。4、 固化劑：本產品為單組份油墨，如有特殊要求也可選擇添加固化劑增加附著力及墨層抗性。5、 油墨調配：充份攪拌后取所需用量進行調配使用，雙組份油墨先按比例添加固化劑攪拌均勻，然后再添加稀釋劑稀釋到合適粘度進行印刷；添加固化劑后的油墨超過使用時限會產生粘稠膠化現象，請及時清洗網版，并棄用油墨，不可回收。6、 網版及刮膠：適合80T-140T（200目-350目）聚脂網紗，聚氨脂PU油性刮膠。7、 干燥條件及時間：本產品可以常溫干燥，也可以烘烤快速干燥，建議干燥溫度及時間為25℃/24小時，60℃/40分鐘，80℃/30分鐘，100℃/20分鐘。8、 性能檢測：用3M600膠帶劃百格測試100%無脫落；用棉布沾95%工業酒精以500G力水平來回擦拭100次無脫色；1mm厚鋁片在印刷位置進行沖斷、卷邊、延壓后邊緣位置100%無脫落；9、 包裝規格：1KG/膠罐，12罐/箱。10、儲存條件：置于干燥通風處常溫保存；避免高溫、太陽直射，嚴禁煙火。11、注意事項：請向我司索取《MSDS安全使用手冊》，并按指引進行安全生產。?Glass screen printing resistant acid and alkali ink1, applicable materials: metal, electroplating, alumina, electrolytic plate, aluminum plate, spray paint, spray (baked), PA nylon, bakelite plastic, glass steel, melamine etc..2, product characteristics: half light, no baking, alcohol resistance, stamping.3. Diluent: the company's B-03 diluent or 783 slow dry diluent.4, curing agent: This product - ink, if there are special requirements can also choose to add curing agent to increase adhesion and ink layer resistance.5, ink deployment: fully mixing after the dosage required for the deployment, two-component ink first adding curing agent according to the proportion of mixing evenly, then add the diluent to the appropriate viscosity of printing ink; curing agent is added after more than the use of time will produce viscous gel phenomenon, please clean the screen, and abandoned ink Unrecyclable.6, screen and frictioning: for 80T-140T (200 -350 mesh) polyester mesh, polyurethane PU oily frictioning.7, drying conditions and time: This product can be dried at room temperature or dry quickly. It is recommended that the drying temperature and time should be 25 /24, 60 /40, 80 /30, 100 /20.8. Performance testing:Use 3M600 tape to make 100 lattice tests 100% without falling off.With cotton cloth, 95% industrial alcohol was wiped back and forth at the level of 500G force for 100 times without decolorization.The position of 1mm thick aluminum sheet in the printing position is broken, curling, and the edge position after the pressure is 100% without falling off.9, packaging specifications: 1KG/ glue cans, 12 cans / boxes.10. Storage conditions: keep at room temperature in the dry and ventilated place; avoid high temperature, direct sunlight, and strictly prohibit fireworks.11, attention: please ask our department "MSDS safety manual" and carry out safety production according to the guidelines.